Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 10, 2013 20:24:40 GMT -5
Most of the 10 inch rims I have seen uses 300. or 350 size tires. I beleave if you go that big you need a wider rim. just rember the muffler has to have room away from the trie as well.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 10, 2013 8:35:02 GMT -5
Whats the best way to tune your carb on a gy6 or qmb moped for when the weather gets cold.I have been haveing hard start prolems. ounce started its good but takes some time to get going. If I heat the bike up with a small light or heater the bike startes right up.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 7, 2013 8:48:33 GMT -5
sounds like elec choke is bad. Whats the weather like there. If cold place some heat buy the scoot for a little befor sarting. All you need is a 100 w light siting buy the scoot on the floor for a few.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 6, 2013 16:27:49 GMT -5
have it weldeded back togthr.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 4, 2013 19:04:55 GMT -5
check all parts under the kick start cover if you use the kick start a lot. things happen. give it a good look over.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 1, 2013 18:57:16 GMT -5
good going. and als0 you can patch tires from the inside with a batch.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Oct 1, 2013 18:52:55 GMT -5
you can drill out the zets with a dremel drill or some small fine drill bits.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 28, 2013 13:34:32 GMT -5
If you are haveing a hard time with the flow of gas with gravty flow drill small hole in the gas cap.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 27, 2013 7:53:59 GMT -5
someimes a smaller gas line will work with gravty flow. and a smaler gas filter. I have my scoot hooked like that and no shot off. just line goin from the tank to the carb.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 25, 2013 18:41:38 GMT -5
thats the way to go.I have both my scoots useing 20 mm carbs. gives theam 50cc a little extra push. I have one extra but im keeping it or back up. they hard to find. you can take dremel drill and horn out the opening of the carb. it works,
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 22, 2013 20:23:27 GMT -5
wow the only thing I can think of is a higher power impact. take it to a shop so thy can take it off.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 22, 2013 20:19:32 GMT -5
check your valves.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 21, 2013 19:02:34 GMT -5
If its not the battery check the red wire comeing of the elec relay. See if you are geting power from it.But check for power when scoots runing.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 21, 2013 18:53:55 GMT -5
From the canaster there should be a line on it going up to a T then from there one on the head and one to the gas tank. and the last one to the carb.
|
|
Freshman Rider
Currently Offline
Posts: 77
Likes: 1
Joined: Feb 26, 2013 21:10:09 GMT -5
|
Post by rae4180 on Sept 19, 2013 21:11:57 GMT -5
Rae1480, Yes that is a pull start, my trike in Sig came with it. Alleyoop mmm That gives me a idea for my 50 cc moped. my kick start is broken and I aready have pull start laying around.
|
|