|
|
Post by millsc on Mar 26, 2014 19:09:30 GMT -5
|
|
|
|
Post by millsc on Mar 25, 2014 22:25:52 GMT -5
I put in 17/36 gears helped a bunch can cruise at 65 on the 55 mph highway and keep up with traffic at 3/4 throttle which is probably 55 GPS. I lost my license a few years back for child support and rode my modded 50cc for a bit without a license but got it all paid off and now I have a motorcycle license and insurance its awesome to be 100 percent legal.
|
|
|
|
Post by millsc on Mar 20, 2014 20:59:45 GMT -5
I got a good boost with my p&p exhaust especially in acceleration but mine is maxed.
|
|
|
|
Post by millsc on Mar 14, 2014 21:37:12 GMT -5
Its very unlikely a 150 with stock gears is capable of those speeds mine wouldn't hit over 65 GPS even with the 15 37 set had to go to 17 36 to reach the speeds im getting and you need a bbk and a stroker to run that tall of a gear.
|
|
|
|
Post by millsc on Mar 14, 2014 21:27:21 GMT -5
75 real mph seems far fetched unless you are going downhill and have a tail wind mine did 71 GPS on the highway with a slight tail wind but I have a very tall gear and have modded the heck outta it my Speedo was maxed at 80.
|
|
|
|
Post by millsc on Mar 14, 2014 21:22:13 GMT -5
Never heard of this.
|
|
|
|
B-CASE?
by: millsc - Mar 14, 2014 21:18:37 GMT -5
Post by millsc on Mar 14, 2014 21:18:37 GMT -5
I bet the 232 on a 150 would be quite a bit faster than a 250 the 150 is much lighter.
|
|
|
|
Post by millsc on Mar 14, 2014 19:42:24 GMT -5
A 50mm gasket should work or cut a stock one you'll have plenty of piston to head clearance with two gaskets.
|
|
|
|
Post by millsc on Mar 14, 2014 7:35:20 GMT -5
|
|
|
|
B-CASE?
by: millsc - Mar 12, 2014 22:51:48 GMT -5
Post by millsc on Mar 12, 2014 22:51:48 GMT -5
I wouldn't go over 62mm on a standard case, the 61mm required no boring and combined with my stroker its plenty enough for where I ride, actually overkill.
|
|
|
|
B-CASE?
by: millsc - Mar 12, 2014 22:43:05 GMT -5
Post by millsc on Mar 12, 2014 22:43:05 GMT -5
For sure takes a b case the standard cases can only be bored to 63mm the 232 takes a 67mm and a 8.2mm stroke.
|
|
|
|
Post by millsc on Mar 12, 2014 20:16:30 GMT -5
all my new scoots smelled hot for awhile, and thats with a new rejetted carb.
|
|
|
|
Post by millsc on Mar 11, 2014 20:13:25 GMT -5
|
|
|
|
Post by millsc on Mar 10, 2014 21:59:55 GMT -5
I'm very pleased with the 17/36 set good upgrade, not sure if they would work without the stroker but was worth the money.
|
|
|
|
Post by millsc on Mar 10, 2014 20:52:13 GMT -5
Got it all switched this evening i didn't lose any torque or acceleration and gained around 7 mph on the top end, i guess i'll just go easier on the throttle  |
|
