|
|
Post by millsc on Feb 19, 2017 11:09:03 GMT -5
75 degrees in February it's time
|
|
|
|
Post by millsc on Aug 20, 2016 9:18:35 GMT -5
Taida 61mm kit works perfectly no case boring 50 plus shipping
|
|
|
|
Post by millsc on Aug 20, 2016 9:16:23 GMT -5
Taida 61mm kit works perfectly no boring the case 50 plus shipping
|
|
|
|
Post by millsc on Aug 20, 2016 9:10:21 GMT -5
I've been running the taida 61mm for awhile along with the 3mm stroker yesterday it developed a leak I'm sure at the base. I used the spacer no gasket with red gasket sealer it held up for nearly 3k miles. So since I have to tear it apart might as well go bigger going to install the taida 63mm with forged piston. They now have 1mm spacers so I'll use it with a gasket on each side instead of the 1.65mm without gasket. Btw I'll have a taida 61mm kit for sale that works perfectly I'd take 50 bucks for it plus shipping cost.
|
|
|
|
Post by millsc on May 20, 2016 19:10:09 GMT -5
It should be prelubed i put engine oil on them the a14 is a good cam i went from a14 to a12 its sligtly better
|
|
|
|
Post by millsc on May 13, 2016 21:12:15 GMT -5
A got my a12 installed today got my bottom end back plus higher top speed the a9 performs close to stock the a14 has great bottom end lowers your rpm by a few grand. The a12 is the way to go seems to have both spectrums im very pleased with it.
|
|
|
|
Post by millsc on May 9, 2016 22:46:51 GMT -5
Ive been running an a14 with my setup its been awesome i did a valve adjustment this weekend and my a14 bearings were sloppy so i had an a9 cam so i decided to try it.
It not near as good as the a14 lost top end and low end torque. So i ordered an a12 to see how it performs if it isnt as good ill buy another a14.
|
|
|
|
Longer belt?
by: millsc - May 9, 2016 22:41:14 GMT -5
via mobile
Post by millsc on May 9, 2016 22:41:14 GMT -5
I run the 842 belt instead of the 835 its longer didnt really notice any improvement but it could help so i use it lol
|
|
|
|
Post by millsc on May 6, 2016 20:00:08 GMT -5
They are 34 bucks why not
|
|
|
|
Post by millsc on May 6, 2016 19:51:25 GMT -5
Do the gears its easy get the 17/49
|
|
|
|
Post by millsc on May 6, 2016 19:47:48 GMT -5
Ive tried 16/42 16/50 and 17/49 i like the 17/49 the best stock varaitor and 5 gram dr pulley sliders i weigh 180. Btw the 52mm ncy bbk is the best with the hoca 52mm a close second then the airsal 50mm if you can find one.
|
|
|
|
Post by millsc on Mar 24, 2016 20:02:40 GMT -5
 Bigger pic |
|
|
|
Post by millsc on Mar 24, 2016 19:51:17 GMT -5
It was fairly simple no gear to press out like in the 150 no extra gaskets spacers or anything
|
|
|
|
Post by millsc on Mar 24, 2016 19:48:54 GMT -5
|
|
|
|
Post by millsc on Mar 24, 2016 19:47:48 GMT -5
|
|
