|
|
Post by crawford on Aug 12, 2016 14:04:04 GMT -5
As usual some don't read or understand what I wrote tires from Goodyear are also made in china and that's china control. Remember our government controls the meaning of what and how it's made so many company's do minimal just to slide by the standards Government sets
|
|
|
|
Post by crawford on Aug 12, 2016 9:09:38 GMT -5
The other system isn't for reverse bleed I have that also just not that company.
|
|
|
|
Post by crawford on Aug 12, 2016 9:08:00 GMT -5
Phoenix Systems 2104-B V-5 Reverse Brake and Clutch Bleeder This is the system I use works great and your not banging your head against the wall LOL
|
|
|
|
Post by crawford on Aug 11, 2016 20:39:31 GMT -5
Remember the stroke you move is very little it takes a long time till all air is gone. I use a reverse bleeder everyone know air wants to go up much easier not fighting the way air moves.
|
|
|
|
Post by crawford on Aug 11, 2016 11:56:33 GMT -5
Tires in general are all the same as far as I'm concerned. Story camping next store camper starts a conversation about tires I mention I went to G load range made in china because couldn't find any USA tires. I says to me I would never put on China tires he buy Goodyear. Later that day I was at his camp site happen to look at his Goodyear tires guess were it was made yep china LOL. I called him over and showed him was it said he nearly fell over and said you bet he will be going back to dealer over that. I then googled goodyear tires found they have 6 plants in china. You just never know so that's my point. Our government like fuzzy math like a tire 2 ply this and 2 ply that and 2 ply is rated as 10 ply our government is our worst enemy on safety of tires IMO
|
|
|
|
Post by crawford on Aug 6, 2016 18:41:22 GMT -5
you need a better look at intake then that what you did , did nothing at all.
|
|
|
|
Post by crawford on Aug 5, 2016 20:00:04 GMT -5
check vacuum line from fuel shut off with vacuum to carb and to the valve it needs to be connected to get constant fuel to carburetor are valve my be not working.
|
|
|
|
Post by crawford on Aug 5, 2016 19:48:59 GMT -5
with 8,000 miles look at rubber intake see if it's got cracks bad vacuum leaks can do it.
|
|
|
|
Post by crawford on Jul 30, 2016 21:28:00 GMT -5
It either wasn't seated on rim right or it was a bad tire from the start.
|
|
|
|
Post by crawford on Jul 24, 2016 21:34:29 GMT -5
most list top on gasket since you see the leak pull the head and look at leak area.
|
|
|
|
Post by crawford on Jul 24, 2016 14:21:43 GMT -5
Why not bring it to a auto parts store and get the right one.
|
|
|
|
Post by crawford on Jul 24, 2016 13:11:31 GMT -5
You did put on new head gasket right ?
|
|
|
|
Hello All!!
by: crawford - Jul 22, 2016 21:27:12 GMT -5
Post by crawford on Jul 22, 2016 21:27:12 GMT -5
Welcome our forum
|
|
|
|
Post by crawford on Jul 20, 2016 21:14:07 GMT -5
I don't know about being slow but my wife and I are out riding or trikes  |
|
|
|
Post by crawford on Jul 20, 2016 8:43:44 GMT -5
yes well will have to, we also have 2 of them LOL get back yo you going to take Grand kids to Dollywood by
|
|
