New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Nov 4, 2013 23:30:57 GMT -5
I should look into reconditioning a battery. I put a old scooter battery in a HB freight ultrasonic cleaner just for fun, well that battery has giving him no problems! I have done twice and both batteries have plenty of power now! |
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Oct 6, 2013 19:37:44 GMT -5
I'm swapping an used 50cc into a "WildFire 50cc", the stator has different connector !
My question is must I use a flywheel puller to swap the stator?
Can I rewire the conector? ( cut and splice ) ?
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Sept 10, 2013 11:38:29 GMT -5
I bought a used scooter that he was going to make it 70cc but lacked funds and know how. I'm missing the cylinder cover. but Im unsure what this gasket is for its rubber! any ideas? Attachments:
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Sept 3, 2013 22:58:31 GMT -5
I just found a Keeway Venus that has 39 miles on it! The guy wanted to make it 70cc but ran into hard times and really didn't know what he was doing, so his loss is my gain!
Do you think high temp RTV will work for the base gasket?
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
20mm CVK
by: kattman - Jul 31, 2013 21:37:46 GMT -5
Post by kattman on Jul 31, 2013 21:37:46 GMT -5
I have bought two of the 20mm carbs local. the first one didnt have a holder for the needle just like yours! I found it under the diaphragm! Someone was in a hurry an did not care!!! the scond one the needle holder was right! Also the first one didn;t have a #  main jet either It was a #72  I hope you get lucky and the holder is under it! like me |
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jul 28, 2013 0:06:25 GMT -5
The scooter is a Linhai 50cc 4t qmb139. Its a "Taotao" with a few uncommon parts like the restricter in the pic. fuel sender bolts wit 4 bolts, and the starter relay is a plug like a "yamaha".
The scooter runs the same with are without the restricter connected. I cannot get above 32mph, It's just "splutters" until i back off throttle even down hill.
Do I have a restricted CDI?
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jun 27, 2013 23:18:24 GMT -5
Well I assumed I had a #35, but it was marked #33 and was pluged ! No matter what I do I can not get it clean! so I took a and picked up another pilot jet. The scooter sounded good until I put the seat on. Now its clogged to!
Is there a smaller "Micron Element" fuel filter That I can buy?
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jun 25, 2013 10:38:49 GMT -5
This scooter was sitting for a year with a busted clutch shoe. I replaced the clutch with a used one. I Clean the carb, drain the fuel ( see attach pic ). I tried two other carbs, changed the main jet to a  , 82,  . still no change! Is the stock #35 pilot jet too small if it starts and idles ok? Fuel comes out of the filter freely. Help! Attachments:
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jun 15, 2013 1:33:40 GMT -5
Diode! why does it have an adjuster? "trim POT"? Attachments:
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jun 14, 2013 23:39:59 GMT -5
Any ideas Attachments:
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jun 3, 2013 22:47:53 GMT -5
I just bought this engine, so i do not know if the air filter had a fitting. I don't have it on the other 50cc I have.
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on Jun 3, 2013 8:50:52 GMT -5
I just bought this engine, and have no idea what hose connects to this nipple on the bottom of the transmission . Anyone know what its for? Attachments:
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on May 26, 2013 0:24:55 GMT -5
You are wrong! Good job. A real mechanic disassembles and inspects to determine what parts are needed. Throwing parts at the problem though you might get lucky is always the wrong answer. This guy is an Technician! He took the time to understand the how it works and why it doesn't work! Good Job Cloud!!!! |
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on May 25, 2013 1:35:17 GMT -5
I hope this won't bite you in court! Why did you do it his way ? Your the pro and charged him!
|
|
New Rider
Currently Offline
Posts: 40
Likes: 0
Joined: Mar 6, 2013 11:12:17 GMT -5
|
Post by kattman on May 22, 2013 13:18:48 GMT -5
I have about 700 miles on the OEM belt!
Has your belt gave you any warning before it broke?
|
|
main jet either It was a #72 
, 82, 
. still no change! Is the stock #35 pilot jet too small if it starts and idles ok? Fuel comes out of the filter freely.
