|
|
Post by tvnacman on Nov 2, 2017 20:10:04 GMT -5
I was not being a wise guy, its hard to figure out ones skill set on a forum. Sometimes you just have to come out and ask to be sure.
John
|
|
|
|
stator issues
by: tvnacman - Nov 2, 2017 17:10:31 GMT -5
via mobile
Post by tvnacman on Nov 2, 2017 17:10:31 GMT -5
Are you reading AC or DC Volts from the stator?
John
|
|
|
|
Post by tvnacman on Nov 2, 2017 4:38:05 GMT -5
the new one disconnected shows 60 ohms to ground from both output wires. thats not right, plus it has zero volts out when running I rely more on output voltage than ohming. Temp can effect the reading. John |
|
|
|
Post by tvnacman on Nov 1, 2017 19:12:28 GMT -5
Mine is not plug and play you will need to do the wiring. I have some plugs and pins.
Darrell, the 4 pin regulator can shunt all stator power, that is why you need to up it when testing stator output.
John
|
|
|
|
Post by tvnacman on Nov 1, 2017 4:30:14 GMT -5
it has a sensing wire/line that will increase and decrease regulator output/voltage.
Did you buy the cheap charlie off amazon? if so thats why your getting the run around. I test all my electrical items the defective ones go in the trash.1 in 3 are bad.
John
|
|
|
|
stator issues
by: tvnacman - Oct 31, 2017 13:13:33 GMT -5
via mobile
Post by tvnacman on Oct 31, 2017 13:13:33 GMT -5
|
|
|
|
frustrated
by: tvnacman - Oct 31, 2017 6:21:16 GMT -5
Post by tvnacman on Oct 31, 2017 6:21:16 GMT -5
I suspect you jared something when changing the cable.
I suspect electrical.
John
|
|
|
|
Post by tvnacman on Oct 31, 2017 6:14:59 GMT -5
when your regulator is plugged in it will throw off the readings.
Why would you go with 5 pin and not 6 or 7 with the 11 pole set up?
John
|
|
|
|
stator issues
by: tvnacman - Oct 30, 2017 15:14:37 GMT -5
via mobile
Post by tvnacman on Oct 30, 2017 15:14:37 GMT -5
Are you taking the measurements with the stator plugged in. Is the regulator connected?
John
|
|
|
|
Post by tvnacman on Oct 9, 2017 19:11:57 GMT -5
what size wheels?
John
|
|
|
|
Post by tvnacman on Sept 26, 2017 19:26:04 GMT -5
you would have to probe and trace the wires.
John
|
|
|
|
Post by tvnacman on Sept 24, 2017 17:00:26 GMT -5
It came up a while back it is a relay, I think JR settled this the last time.
John
|
|
|
|
Post by tvnacman on Sept 23, 2017 13:26:02 GMT -5
It's a relay.
|
|
|
|
Post by tvnacman on Sept 16, 2017 17:54:15 GMT -5
have you tired to contact the vendor? If so what was the outcome?
John
|
|
|
|
Post by tvnacman on Aug 26, 2017 6:38:52 GMT -5
where was this sign?
John
|
|
