|
|
Post by jeepsteve92xj on Apr 23, 2013 7:58:23 GMT -5
|
|
|
|
gy6B parts
by: jeepsteve92xj - Apr 22, 2013 20:25:26 GMT -5
Post by jeepsteve92xj on Apr 22, 2013 20:25:26 GMT -5
Bump bump for robrun.
|
|
|
|
Post by jeepsteve92xj on Apr 22, 2013 13:51:51 GMT -5
I had both brake switches go bad on the same day and was lucky I could kick start my 150cc scoot. On my Znen, one switch was bad and the second I suspected of going bad sooner rather than later. The same two DIFFERENT switches as sold by scrappy didn't last at all, and are way too expensive. I bought a couple waterproof mini switches and bent a little plate to mount them onto the Znen, and will do the Xingyue when they start to act up again. Good for like 2amps (I think) and waterproof and less than $3 each from Grainger. www.grainger.com/Grainger/OMRON-SubMiniature-Sealed-Snap-Switch-2KRW6?Pid=searchIf not that one, then it was one without leads, like this www.grainger.com/Grainger/OMRON-SubMiniature-Sealed-Snap-Switch-2KRX9?Pid=searchAnd looking at the price, maybe I should stop and see if I can get a dozen or two. |
|
|
|
gy6B parts
by: jeepsteve92xj - Apr 22, 2013 12:20:44 GMT -5
Post by jeepsteve92xj on Apr 22, 2013 12:20:44 GMT -5
|
|
|
|
Post by jeepsteve92xj on Apr 20, 2013 11:12:41 GMT -5
Yay  I would like to hear any updates on the EFI project. I've bought an ecotron kit, but haven't had any nice weather yet to even ride never mind convert the scooter and work out the exhaust. today is 30F and quite windy, but dry for a change! |
|
|
|
Post by jeepsteve92xj on Apr 20, 2013 9:47:54 GMT -5
I put in a set of slider, and then went back to the original rollers. I dont remember what the weights were, I will have to weigh them and find out. I may do a mixed set next.
|
|
|
|
Post by jeepsteve92xj on Apr 19, 2013 22:47:36 GMT -5
|
|
|
|
gy6B parts
by: jeepsteve92xj - Apr 19, 2013 22:40:27 GMT -5
Post by jeepsteve92xj on Apr 19, 2013 22:40:27 GMT -5
|
|
|
|
Post by jeepsteve92xj on Apr 19, 2013 18:41:20 GMT -5
|
|
|
|
Post by jeepsteve92xj on Apr 19, 2013 16:24:14 GMT -5
Looks just like my Znen.
Mine does not have any sound system, or alarm or remote start, and certainly I never got my Znen to 60mph. 10hp would be nice.
|
|
|
|
gy6B parts
by: jeepsteve92xj - Apr 19, 2013 13:31:11 GMT -5
Post by jeepsteve92xj on Apr 19, 2013 13:31:11 GMT -5
|
|
|
|
gy6B parts
by: jeepsteve92xj - Apr 19, 2013 13:01:38 GMT -5
Post by jeepsteve92xj on Apr 19, 2013 13:01:38 GMT -5
|
|
|
|
gy6B parts
by: jeepsteve92xj - Apr 19, 2013 8:36:42 GMT -5
Post by jeepsteve92xj on Apr 19, 2013 8:36:42 GMT -5
the -B valve cover does use different bolts
two gland style with gasket/rubber washers.
Though with the right length and thread of bolt and some rubber and washers, something could be rigged up well enough to use.
|
|
|
|
Post by jeepsteve92xj on Apr 19, 2013 7:24:12 GMT -5
Dual pistons as side by side or opposed ?  My front caliper looks like that, and the rear looks like opposed. It was raining horses and cows, so I didn't stop too long to look, and didn't take pictures. |
|
|
|
Post by jeepsteve92xj on Apr 19, 2013 7:20:56 GMT -5
What engine model do you have, out of curiosity? On a side note, I probably should have put "CVT Belt Issues" as an option above. Xingyue ITA 150 with the GY6-B. 16" wheels. Soon to be fuel injected if the weather will be reasonable for a day to two! STILL haven't got to ride yet this season. Less than 10 miles anyhow. |
|
