|
|
Post by lostforawhile on Nov 2, 2017 17:17:36 GMT -5
I want to get a cheap one working for the moment, then next month I'm converting to the 11 pole
|
|
|
|
Post by lostforawhile on Nov 2, 2017 17:16:09 GMT -5
well AC of course, I replaced the stator because the charge coil voltage had dropped to the point where it couldn't power the cdi effectively. it starts and runs now, just no voltage output
|
|
|
|
frustrated
by: lostforawhile - Nov 2, 2017 17:13:22 GMT -5
Post by lostforawhile on Nov 2, 2017 17:13:22 GMT -5
why do you think something is wrong inside the engine, when it was running fine before? you broke a throttle cable, that wouldn't make something break inside of the engine. you have a leak, hence the sound coming from under the carb, did you replace the spacer under the intake?
|
|
|
|
Post by lostforawhile on Nov 2, 2017 17:05:51 GMT -5
well it has zero volts out, the resistance isn't going to change that much, a good stator only has a couple o ohms resistance between the wires and ground, a brand new one showing 60 ohms to ground on each, shows something is wrong, my bet is they didn't clean the coating off of the leads ends, and soldered right over it
|
|
|
|
Post by lostforawhile on Nov 1, 2017 23:56:04 GMT -5
it's a float bowl drain, you unscrew the screw in the middle and it drains the bowl. I'm sure someone has one from an old carb, if you have to,cut it off or remove the clamp on the bowl and use a piece of plugged off hose in the meantime until you get one
|
|
|
|
Post by lostforawhile on Nov 1, 2017 21:25:24 GMT -5
got an orange CDI I thought I had given them all away, it has too much advance for me
|
|
|
|
Post by lostforawhile on Nov 1, 2017 21:09:55 GMT -5
it will probably be next month before I can get that 11 pole, I have put so much money into this thing to get it running. As long as you have the plug and pins for the regulator, the rest is simple as long as I can find a pin out and diagram, I will most likely put a weather pack connector on the stator output anyway
|
|
|
|
Post by lostforawhile on Nov 1, 2017 21:06:16 GMT -5
the new one disconnected shows 60 ohms to ground from both output wires. thats not right, plus it has zero volts out when running
|
|
|
|
Post by lostforawhile on Nov 1, 2017 11:29:29 GMT -5
|
|
|
|
Post by lostforawhile on Nov 1, 2017 11:23:25 GMT -5
Yep, hand rotary crimper, you can get the silicone boots on ebay, I need to get another rotary crimper for home, as mine was stolen, have to use the one at work
|
|
|
|
stator issues
by: lostforawhile - Nov 1, 2017 11:09:19 GMT -5
via mobile
Post by lostforawhile on Nov 1, 2017 11:09:19 GMT -5
I'll get the 11 pole setup from John does that come with the connector plugs? Or do you have to source your own plugs and wiring? I want to add some aux driving lamps anyway so I need the wattage
|
|
|
|
stator issues
by: lostforawhile - Nov 1, 2017 11:07:26 GMT -5
via mobile
Post by lostforawhile on Nov 1, 2017 11:07:26 GMT -5
I found an x pro one, at a regular online scooter store, and back searched it to amazon, got it with free shipping, I hate to spend a bunch of money,when I'm going to convert to the 11 pole anyway
|
|
|
|
Post by lostforawhile on Oct 31, 2017 22:48:44 GMT -5
|
|
|
|
Post by lostforawhile on Oct 31, 2017 22:46:39 GMT -5
amazon screwed up my order, so the ride is off, I won't get a stator in time. I have to ride with someone else in one of the cars, the scooter will start now with not even one revolution, but no power for the lights or battery charge.
|
|
|
|
Post by lostforawhile on Oct 31, 2017 19:31:18 GMT -5
so that one has a feedback to keep the battery from overcharging?
|
|
