New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on May 4, 2014 20:18:40 GMT -5
For 800 bucks she did not walk away. She RAN!!! Thanks for your advice.
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on May 3, 2014 22:07:53 GMT -5
 I have a friend that is looking at a Konced 150cc scooter year 2008. It needs a new battery, and a rear tire. That is all she could tell me aboyt it. She is going to go look at it tomorrow 5/4/14. Any advice you can through at me would be help full.. Right now my advice to her would be stay away.
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Apr 13, 2014 14:12:27 GMT -5
 How do you hold the clutch to get the big clutch nut (inner one) to the right torque before you reinstall it on a scooter?
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Mar 30, 2014 18:56:38 GMT -5
Do not have a lot of sharp curves where i live. I have leaned over that much.. The pegs are on a hinge, and they fold back. most of my riding is on flat ground.
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Mar 30, 2014 17:08:11 GMT -5
thatade these for my Buddy 170. Though this might give someone ideas Foot pegs METE RIALS 3/16 X 1in. X 4 foot is stainless steel flat iron. (Free local junk yard) Foot pegs, local bike shop. Same price as his, but no shipping! Longer metric bolts. (M6-1.0x30mm) Auto Zone. Small pieces of Velcro. Now the fun part. Measures, cut, bend the center piece. Measured from different points to get the bolt down holes right. Drill holes 2 sizes bigger to allow for a little adjustment. Did not like where my feet were going to be, to cramped, so I cut 2 pieces 7 inches long wielded then to the cross piece. Next thing they were a little to low, so I notched the 7 in. pieces and bent them up a little. Next the pegs slanted down a little so I twisted them up a little. Then said that’s good enough, and welded then solid where I had notched them. Work grate! you can not put a lot of weight on them, but they are grate for stretching out your legs. The Velcro went in the inside of the bend of the cross piece, so nothing would scuff the plastic. I am enclosing pictures from Photo bucket, hope they turn out. Up date: Added a clip on each side to hook on the frame. This took the stress off the two floor board bolts. Worked great! Project done.     Hope this gives somebody ideas! |
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Mar 13, 2014 22:26:56 GMT -5
Put new liscens tabs on. Still under winter wraps in Minn.
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Feb 8, 2014 16:29:36 GMT -5
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Jun 18, 2013 19:59:23 GMT -5
 Put some coffee behind your lower lip, like snuff! Stays with you a long while, due not have to make pit stops all the time, and something to munch on! and do not have to wore about spilling it! Try it you will like it! 
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on May 14, 2013 20:05:01 GMT -5
 My mirror on the left side is starting to come loose. How do i get the mirror off so i can tighten it? I saw a thread someplace that had photos on how to do it, but can not find it again. Thank You issue31
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Apr 2, 2013 16:57:14 GMT -5
;D And it's only the BEGINNING!!!!!!! Thanks guys great forum
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Minnesota
by: issue31 - Mar 21, 2013 19:32:10 GMT -5
Post by issue31 on Mar 21, 2013 19:32:10 GMT -5
issue31, J.F.Smith
Plainview, MN.
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Mar 21, 2013 19:22:22 GMT -5
 Thanks Terrilee.
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Mar 5, 2013 15:02:57 GMT -5
Finely issue31 has made it to "It Is The Ride" It took a while but I got here!
|
|
New Rider
Currently Offline
Posts: 17
Likes: 0
Joined: Mar 3, 2013 10:56:59 GMT -5
|
Post by issue31 on Mar 3, 2013 12:29:37 GMT -5
 after jumping through a lot of hoops i finely got here! issue31
|
|
My mirror on the left side is starting to come loose. How do i get the mirror off so i can tighten it?