New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Jul 19, 2018 19:52:23 GMT -5
Thanks tortoise for your reply. I started at their site www.ecobike.com , they said to ask questions about parts, go to manager@ecobike.com , I did but it would come back undelivered. So I finally got them at dave@motofino.com . I sent them an email to see if they have the parts (not listed) waiting for a reply. |
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Jun 21, 2015 18:53:05 GMT -5
They are one of my "Top of the List". Very helpful people and decent prices !!.
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Aug 2, 2013 21:36:16 GMT -5
OOP's I found it  ,, Same place I found it three years ago  ..Duh. |
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Aug 2, 2013 21:28:23 GMT -5
, ;X, I found the info I was looking for.. Same place I did three years ago,,, duh !! Maybe I need a walker and white cane ??!!.
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Aug 2, 2013 19:01:50 GMT -5
Can any of you learned gents tell me where I can get a clear diagram of how the kick start gears are supposed to be positioned. I have a 150cc Znen Pacifica.. I found some info on a forum but it doesn't seem to be setting up right. Mine came apart when I removed the CVT cover to change variator weights.. I can get the marks lined up, but when I start it, it runs ok but it sure doesn't look like when I lined it all up.. This may not make much sense but I sure would like some help on this..
I know there can't be a Sticky on everything, but I see very little info on this problem, what category would it fit under,, Engine,, CVT area ?.. Thanks a lot..
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Aug 2, 2013 14:51:25 GMT -5
Hello scooter150cc.. I also have a Znen 150 Pacifica SSR. Do you have any help angles on realigning the kick start gears and spring ?. When I took the cover plate off, the gear assembly came apart. I found a couple examples but they don't match my assembly.. Thanks for any help..
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Jul 21, 2013 12:42:41 GMT -5
Thank you all for the replies !!. I figure the 16" wheels will show more lugging on take off vs smaller wheels. Is there much diff. between say 11g sliders and 11g rollers ?.. I may try the 10g also.. Yes, I put Sea foam in the gas.. Thanks again,, This is a good forum  |
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Jul 20, 2013 17:31:10 GMT -5
|
Post by epdowd on Jul 20, 2013 19:22:51 GMT -5
Hello, I haven't been on the forum for a long time,, back when it was S/D..My question is: I would like to find the correct slider weight for the variator. The scoot is a 2009 Znen 150T. It has 12 gm sliders in it now and lugs pretty bad on take off. Good top end 60mph. I will have to go with lighter weights the way I understand it. Is there a weight you would suggest ?. I weigh 190. It's a small town and I don't need a lot of speed. What advantage are different springs ?.
Thanks for the help.. Harv..
|
|
