New Rider
Currently Offline
Posts: 45 
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Sept 6, 2016 19:19:34 GMT -5
My scooter was shutting down again I thought i had it fix the funny thing was when i got in the seat it would stall. Found out it was a loose wire behind the starter relay when I sat on the seat the storage compartment lean against the relay which lean against the wire harness. Maybe your and my scooter wanted the summer off.
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Aug 13, 2016 21:36:54 GMT -5
I end up putting a y in the fule line on the tank it self one line to another y before the fule shut off another line from the vacuum pump to the second y that way i have gravity feed right from the fuel tank to the carburetor or vacuum pump it fix the problem.
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jul 29, 2016 21:41:42 GMT -5
Update on Vento 150
I replace the coil it started up then i ran the scooter around my apartments then it died again this time I checked for gas in the fule filter it was bone dry.
Check and found out the vacuum hose was disconnected from the carburetor i replace the hose now it seems to run good.
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jul 28, 2016 13:55:39 GMT -5
My 150 vento Scooter is doing the same thing lights are dim until I get over 20 mph. I replace the voatage regular no help. the pick up was replace last year along with the stator . until today it would act up line not getting enough gas I let it sit a half hour later it would start right up again and run a hour before it would act up until today in had to push the little basterd 2.5 miles to get it home I will check for loose wires I have a spare coil and cdi unit. I was thing carb I replace it 4000 miles ago . this scooter has over 14000 miles on it may be time to replace it I plan on waiting till next year so I can buy a 3 wheeler .
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jun 19, 2016 13:03:39 GMT -5
My 2004 Vento 150 with 13900 the tech needle is all over the place on low rpm as well the one light is weak my question is it the voltage regulair or the stater? I did replace the stater last year every thing seams to work at 6000 rpm. or better.
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jun 10, 2016 20:52:30 GMT -5
Try a 90s Honda key blank
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Rong Stater
by: lhumpolick - Aug 6, 2014 19:24:23 GMT -5
Post by lhumpolick on Aug 6, 2014 19:24:23 GMT -5
Need a little help
I'm replacing my 6 Pole stater on a 2004 Vento 150 The Fly wheel said 125
I got in the mail today one with the rong plug please look at the drawing i made can I sub the blue/white for the red white pick up?
Red/Black for the green one?
Or try to find another new one i need asap
Thanks for the help
Could not add file
I have no problem splicing wires
Old plug Clip On Top
4 Squire Plug
Top left white Top right Green
Lower left yellow Lower right no wire
Red/black not in plug
Red/white goes to pick up
New unit Clip On top
Wider 4 pin conector retingler
Top left white Top right Yellow
Lower left blue Lower Right red
Green wire not on plug
Blue/white goes to pick up
One other question
I have two 8 pole stators with the magino can i replace it with one of them?
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jul 30, 2014 23:37:29 GMT -5
I paid $1.99 at hill hardware in Burton Ohio
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jul 28, 2014 23:23:53 GMT -5
It is a honda motorcycle blank by Hy-ko #Hd74 (no computer chip type) from my local mom and pop hardware store Or check out www.hardwarestore.com/ has them it show you a photo |
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jul 28, 2014 15:51:11 GMT -5
Yes That's it
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jul 27, 2014 22:34:12 GMT -5
For your info
I had a oil leak under the scooter the bottom left side was cracked from the kick stand hitting it I tried everything nothing work until i used JB weld gas tank sealer it can be bought at your local hardware store it is one of those putty type in a blue tube you put in your hand to activate it it works under water too it did the job it was hard as a rock in a hour i was ready to buy a motor this was a last ditch effort be for replacing it I hope this helps any body with a crank case leak
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Jun 5, 2014 23:39:46 GMT -5
I went to my local Honda dealer and had the curve ones I had them replace both when i replace the tires. The bad news it cost me $10.00 extra for each one of them so far a year and a half later no leaks.
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on May 11, 2014 23:12:51 GMT -5
I need a little help on my Vento 150 with 11,000 miles
My left hand is due to be worked on(I cracked a bone in my palm of my left hand) every time i hit the rear drum brakes it puts too much strain on my left hand and it's not easy to ride. Is there any way to get the rear brakes to work with less pressure?
Until i can find a fix for the brakes i get a lot of walking in now instead of riding the scooter.
My plan B is to ride rthe Wildfire 50cc whitch takes less pressure to use them.
Thank You for any advice you have on this
Larry H
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Apr 15, 2014 0:07:31 GMT -5
Not here in Middlefield they tried the horse dippers idea did not work out the bishop would not aloud it. One thing we do get is new roads a lot quicker then other cities . For your info a Amish man complain because the horse hit a chuck hole on a back road and wanted the city to pay for it to the tune of $2500.00 for the value of the horse and the cost to have it shot road right there on the spot .I don't know what they did with the horse.
|
|
New Rider
Currently Offline
Posts: 45
Likes: 1
Joined: Mar 20, 2013 23:26:39 GMT -5
|
Post by lhumpolick on Apr 13, 2014 23:17:22 GMT -5
My kids and I own Fatkat Computers and what has work so far is i pulled the magnets from apx 6 hard drives and use zip ties to secure them so far after 2 years they seem to work very good. One issue i have they will pick up every nut,nail and other metal Scrap off the road plus where i live in Middlefield Ohio lets put it this way it's not the dirt that gives me a border line reading it's the Midwifed mud that makes it a pain to clean because where I'm at Middlefield has the 4th largest group of Amish families living here and their horses are not house broken. on a hot day you can't mist the smell..
|
|
