New Rider
Currently Offline
Posts: 10 
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 30, 2016 13:04:41 GMT -5
Yeah, the same bike just came in for a blinker relay, he wired both light to be on, its only 1 at a time
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 20, 2016 16:52:51 GMT -5
That could be a bad petcock, but if your carb float is working right it should stop it anyways.
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 20, 2016 16:51:03 GMT -5
It will not drain the battery unless something is setting off a warning, which can be fixed my adjusting sensitivity, I sell them shipped for $14.99
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 20, 2016 16:49:34 GMT -5
A lot of bikes are setup like that, i just started a thunder i have here and both headlights are on, same for brights
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 20, 2016 16:48:07 GMT -5
First and easiest, check to see if the pickup coil is hitting the magneto, if not then you do get some odd sounds out of a starter clutch going bad. Get the Ban Jing if you need to replace it, then its your last one for good. Theyre only 39.99
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 6, 2016 18:52:15 GMT -5
The BN157QMJ engine are setup to take a 16" wheel, hard to find the whole engine though.
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 6, 2016 18:48:13 GMT -5
So what I've seen in my shop as the number one cause of bearing failure is the variator, the brass sleeve gets worn out and its not tight on the boss which causes an unbalanced weight spinning on the crank, I havent seen any directly caused by big bore kits, at least if they are broken in right and warmed up, but thats on my installed kits. There are kits out there from mortch and growsun that have too tall of a piston, they will run great for short trips but when the engine heats up to its max the connecting rod will expand to the point where the piston hits the head or valves which will blow the connecting rod bearing very fast. The jet size option was a must for me, not a lot of places have it, but say you were to order a kit and a carb I would look at your local weather and elevation and re-jet the carb to work where you live before I shipped it. And good idea, I will now send an exhaust gasket with every order.
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 6, 2016 15:11:27 GMT -5
Not your run of the mill bore kits, we have tested over 20 factories kits and this is the best we have found, with over 3000 installed in our shop they have a great record of running with no problems. The kits will come with the rings pre-gapped, clocked, and installed on the piston. $39.99 shipped to all 50 states. We are also happy to give you help on all install questions, torque values, clearances or jetting through email, phone, or skype video. For the 139QMB, will NOT fit baja sc50
|
|
New Rider
Currently Offline
Posts: 10
Likes: 0
Joined: Dec 6, 2016 13:17:32 GMT -5
|
Post by thescooterguru on Dec 6, 2016 15:05:53 GMT -5
Easy hookup, most bikes install with 1 plug already in bike, if you need to manually wire it in Ill send you a pigtail. Adjustable sensitivity, 2 remotes. Brand new
|
|
