New Rider
Currently Offline
Posts: 8 
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
Post by kauaiboys on Oct 11, 2013 2:16:54 GMT -5
So what kind of rim would it require?
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
Post by kauaiboys on Oct 10, 2013 18:13:02 GMT -5
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
GY6 vibration
by: kauaiboys - Oct 2, 2013 23:33:39 GMT -5
via mobile
Post by kauaiboys on Oct 2, 2013 23:33:39 GMT -5
All good. I have a short case 150cc.
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
GY6 vibration
by: kauaiboys - Oct 2, 2013 2:03:42 GMT -5
via mobile
Post by kauaiboys on Oct 2, 2013 2:03:42 GMT -5
Thanks guys. I did open it up and drove it all day open. Vibrated even more it seemed. I will change the belt this month. The inside of the cvt case was spotless as well. Really frustrating because I want this scoot to run perfect.
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
Post by kauaiboys on Oct 1, 2013 23:54:12 GMT -5
how many miles on the bike, and what kind of belt are you running? Also when did you check the wights last? Tires good? The bike had 1500 miles on it. The owner basically ran it without oil then I got it and replaced the cylinder and piston, starts up and runs pretty good now. I have put about 200 miles on it since the rebuild. - It has the Original belt that comes stock with Short Case GY6. - Haven't checked the weights, because its so new I thought they would be fine. How do I troubleshoot this? |
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
GY6 vibration
by: kauaiboys - Oct 1, 2013 23:01:15 GMT -5
via mobile
Post by kauaiboys on Oct 1, 2013 23:01:15 GMT -5
I tested this on the center stand. It didn't really vibrate like when I'm riding it. I weight 230lbs. So I weigh quite a bit. Not sure if it's the cvt. took the cover off and rode today and it still vibrated loudly at 35mph and higher.
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
Post by kauaiboys on Oct 1, 2013 22:55:32 GMT -5
Thanks for your help. And to answer your question. There Is no backfire whatsoever. I ordered a new carb because they are only $30 on ebay. Hopefully that will fix it.
|
|
New Rider
Currently Offline
Posts: 8
Likes: 0
Joined: Oct 1, 2013 20:24:14 GMT -5
|
Post by kauaiboys on Oct 1, 2013 20:26:03 GMT -5
GY6 Missing on Deceleration. I just put a new cylinder and piston in and its been running great. Its a ruckus clone with a gy6 short case 150cc engine. When I am giving it throttle it sounds good, but when I let off if really feels like its trying to slow down to a stop, I have no idea why it would be like this. Also, when I leave it idling the engine sounds like its not staying at a consistent rev, Also does this when I let off the throttle at low speeds and the bike jerks slightly as it decelerates. Any help would be great. Thanks!
|
|
/10 on this stock rim that came with my ruckus clone? Could I fit the same on the back on the shortcase with a stock rim and Shock? Any help and knowledge would be great. I don't have the money for a long case and i'm not looking to do a fatty either. Just want some beefier tires on this thing. Thanks! Front is Disc and rear has a hub brake. 
