New Rider
Currently Offline
Posts: 21
Likes: 0
Joined: Sept 21, 2013 19:17:43 GMT -5
|
Post by gsragtop on Sept 22, 2013 20:12:38 GMT -5
So I just spent the last 45 min trying to get the bolt that holds the rear tire off.. I tried a beaker bar, liquid wrench, impact wrench, torch.. Everything I could think of, and it did not budge not one little bit... What am I missing???
|
|
New Rider
Currently Offline
Posts: 21
Likes: 0
Joined: Sept 21, 2013 19:17:43 GMT -5
|
Post by gsragtop on Sept 22, 2013 14:04:07 GMT -5
|
|
New Rider
Currently Offline
Posts: 21
Likes: 0
Joined: Sept 21, 2013 19:17:43 GMT -5
|
Post by gsragtop on Sept 21, 2013 23:09:56 GMT -5
Just took another look at mine, and I don't think the case will split like that.. I think on mine the rear wheel will have to come off then maybe the case splits from that side.. Does this make sence??
Also found the clutch bolt in the front compartment so the DSPO was absolutely in hear messing around..
BTW thank you so much for your help !!
|
|
New Rider
Currently Offline
Posts: 21
Likes: 0
Joined: Sept 21, 2013 19:17:43 GMT -5
|
Post by gsragtop on Sept 21, 2013 22:02:20 GMT -5
Ok so do I have to remove more of the case to reinstall the driveshaft?? Where can I find the correct procedure ??
|
|
New Rider
Currently Offline
Posts: 21
Likes: 0
Joined: Sept 21, 2013 19:17:43 GMT -5
|
Post by gsragtop on Sept 21, 2013 20:29:09 GMT -5
No I don't think it was run dry, I think the DSPO (dip s h * t previous owner) opened it and had no idea what to do.. That's why the clutch bolt was missing, otherwise it should have been in the case.. The ring gear for the back wheel is fine, all teeth there etc..
So what holds the shaft into the case?? When you tighten the clutch on what keeps it from just popping out?? Where can I get the herring and what lube do I use in the case?? Thanks
Ps the scooter only has 750 miles on it..
|
|
New Rider
Currently Offline
Posts: 21
Likes: 0
Joined: Sept 21, 2013 19:17:43 GMT -5
|
Post by gsragtop on Sept 21, 2013 19:33:16 GMT -5
Hello gents, new member to the forum and new scooter owner.. I just got a 2011 Meiduo md50 today off Craigslist.. I knew it was a project, and I only paid $200 for it. It runs great, starts right up idles and revs well.. I was told the guy was riding it home stopped a traffic light and it would not move. First thing I checked was the cvt case and it was missing bolts so I know someone was in there despite the guy swaring he was not in there. Fine, I buy it anyway and get it home. Pull the cover and the clutch bolt is gone, not there clutch just sitting on the shaft. I'm thinking easy fix.. Pull the clutch and notice the final drive shaft (is this the correct term ??) is very loose.. So loose its not attached to anything, I just pulled it right out. Look in the hole, and I see one roller ball in the back of the case so I assume I should have a bearing in there.. Is that what holds the shaft in?? Should the case have lube in there?? It was dry when I opened it. I can't seem to find any info on how the drive shaft should attach..
Thank you in advance guys !!!
|
|
