New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 15, 2013 1:26:37 GMT -5
Nah, dunno wat kit it was, but this was a slightly down hill run.
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 22:50:24 GMT -5
So, as some of you may know, I did a BBK for Metrodee, a member here on the forum. I also, installed the 16/50 gears from scrappy dog, and also a new clutch and carb along with the BBK. I didn't REV the out of the thing, but from what I see as of right now, it probably will top out at 50 MPH. Now, this is with I believe.... -Stock Clutch - 16/50 gears 3.125 Ratio -Stock Carb #  Main -50mm BBK -Orange Coil (needs replacing) -"unlimited" CDI May have left some out up there. The last kit I did for someone did 62 GPS Verified out the box. And had less mods done to it. |
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 22:35:35 GMT -5
annihilation team
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 22:34:10 GMT -5
Common, the rear brake cable is mounted on the engine case.. getting vibrations from the rumbler between your legs, All scooters eventually do this  |
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 21:19:18 GMT -5
is it an aero 80? If so, I can send u a mirror I pulled off mine a while back. O,o
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
It's ALIVE!
by: westendscooters - Aug 14, 2013 21:18:00 GMT -5
Post by westendscooters on Aug 14, 2013 21:18:00 GMT -5
I go .004 and .005, however, I don't know if it same for the 52mm kit. I would assume so.
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 18:03:24 GMT -5
Got it running, hard starts are expected, but damn! Need some fine tuning!
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
scooterdepot
by: westendscooters - Aug 14, 2013 17:46:09 GMT -5
Post by westendscooters on Aug 14, 2013 17:46:09 GMT -5
Sweet!
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 16:51:41 GMT -5
Yeah, I stuck the stock head back on, Sending head in... ill give u a call man!
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 14:58:22 GMT -5
as in, sticking open, getting hit by the piston to close it. FML.
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 14:56:34 GMT -5
00000000000000000000000000000 IT RUNS! but.... one of the valves are smacking. time to return this head.
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 14:08:41 GMT -5
FML. Guide pin missing when I pulled head off, losing compression. -.-
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 13:44:16 GMT -5
Yeah, all new intake stuff, noticed the one that came off was rough, and seals were flat
|
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 14, 2013 13:26:20 GMT -5
I've done dozens of kits for people. This... however is really not going my way, replaced head gaskets 3 times now, rings gaps are staggered, but not facing the wristpins, valves set at .004 on both, stock intake, stock carb - brand new- swapped # jet out of old carb. Spark is pretty weak, (yellow-whiteish). Don't know where else to turn to. |
|
New Rider
Currently Offline
Posts: 26
Likes: 0
Joined: Aug 11, 2013 18:11:51 GMT -5
|
Post by westendscooters on Aug 13, 2013 16:03:47 GMT -5
Been working on putting a BBK on for a forum member here, it's giving me .
I finally got it to have compression, accidentally put the rings in the wrong order...
Now, I was turning it over, and held it wide open, and choked it out, and (note it has a straight pipe) I started getting black-ish smoke out of the pipe. Still no fire. Any ideas? Been trying to start it for 4 days now.
|
|
Main