|
|
Post by triker on Mar 22, 2013 11:32:44 GMT -5
I took delivery of a new engine today. Now I can finally start this project. I could not find a suitable used engine, so I ordered a new one. (from scrappy).
Hoca 44mm stroker crankshaft
NCY 50mm BBK kit
NCY 50mm head
NCY A9 perfomance camshaft
Hoca performance intake manifold
keihin carburetor.
and various other parts.
I will need to order an 8 pole stator and flywheel. I don't want to pull it off the other engine. Also I still need to decide on a variator and clutch. I am not going to use the efi kit on this engine yet, but probably will later on.
Roy
|
|
|
|
Post by teddy554 on Mar 22, 2013 12:15:44 GMT -5
|
|
|
|
Post by triker on Mar 22, 2013 12:29:22 GMT -5
Hey teddy, thanks for that link to the naraku kit. I was leaning toward an ncy clutch and dr pulley variator. I have a polini kevlar belt I am going to use.
Roy
|
|
|
|
Post by teddy554 on Mar 22, 2013 15:56:49 GMT -5
Sorry i didnt check to see, butthey are out of stock and went the 34 dollar on the price racing planet is out of stock to
|
|
|
|
Post by skuttadawg on Mar 22, 2013 15:59:30 GMT -5
Watch out for the stroker eating up variators as it did for Larry
|
|
|
|
Post by devo344a on Mar 23, 2013 10:25:02 GMT -5
Where can you get good prices on steel stroker cranks for the 49cc 139qmbs at i havnt found a place
|
|
|
|
Post by triker on Mar 23, 2013 20:51:12 GMT -5
I found a NARAKU Super trans kit Naraku 669mm - 4stroke 50cc 139QMB Racing Upgrade at this site.www.moxiescooters.com for $217.60
Roy
|
|
|
|
Post by triker on Mar 23, 2013 21:01:36 GMT -5
Where can you get good prices on steel stroker cranks for the 49cc 139qmbs at i havnt found a place As far as I know there is only two manufactures that make a stroker crankshaft for a 139qmb engine. Hoca is one and Scooters To Go is the other. The STG is the cheaper of the two. Roy |
|
|
|
Post by triker on Mar 23, 2013 21:09:21 GMT -5
Watch out for the stroker eating up variators as it did for Larry I am aware of his variator problem. I have been researching this for some time. I have found very few reviews. I am sure that more than one person has tried this and his is the only review that states he had variator trouble. If I do have trouble I will go with a 44mm BBk. Roy |
|
|
|
Post by justbuggin2 on Mar 23, 2013 22:39:35 GMT -5
please take lots of pics and post your build process
|
|
Currently Offline
Posts: 0
Likes:
Joined: Nov 21, 2024 13:47:45 GMT -5
|
Post by Deleted on Mar 26, 2013 13:48:46 GMT -5
Nice post triker
I am curious though...
How are you going to compensate for the extra 1.3mm @ TDC? Stack bases gaskets or a spacer? And will the cam chain length be an issue?
I'm not trying to needle you ~ just curious. Lot's of pics, please!
|
|
|
|
Post by triker on Mar 29, 2013 23:03:57 GMT -5
Well If all goes well tomorrow and I get my to do list done I will start on this project. I will have to use a different carb than the keihin I ordered. The site I ordered from(MX Motorsports) pulled the ol switcharoo and sent me a cheap knock off. Also I ordered copper exhaust gasket rings and they sent regular gasket rings. I'm not going to go into details of the phone call I made to them but I will not recommend them to anybody. So I will be looking for another place to get a Keihin 20mm carb. Any body got a good lead? In the mean time I have a 19mm carb and a 23mm carb but If I use the 23mm carb I will have to replace the throttle cable or modify the cable mount.
Roy
|
|
|
|
Post by triker on Mar 29, 2013 23:23:06 GMT -5
Nice post triker I am curious though... How are you going to compensate for the extra 1.3mm @ TDC? Stack bases gaskets or a spacer? And will the cam chain length be an issue? I'm not trying to needle you ~ just curious. Lot's of pics, please! I haven't decided yet I am going to test fit it first and see exactly how much the piston comes out of the cylinder. If I use a spacer I will still need two base gaskets. I'm not sure about the chain yet, but I don't think it will be a problem. If the chain is to short I will mill off the top of the piston. I need to measure how thick the top of the piston is. I don't want to make it to thin. Or I may try to find a longer chain. But even one link may make it to long. Roy |
|
|
|
Post by triker on Mar 29, 2013 23:53:24 GMT -5
The stock chain is 82 links. I haven't found an  link chain and haven't found extra links. So a longer chain may not be possible. Roy |
|
|
|
Post by millsc on Mar 29, 2013 23:59:28 GMT -5
what is wrong with the throttle cable, i just dremel the the metal on the cable so it goes in father and run 24mm carbs on 50+mm bbks with big valve heads and such take off the base nut
|
|
link chain and haven't found extra links. So a longer chain may not be possible.