Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 3, 2014 16:25:51 GMT -5
is that normal to rotate freely the rear wheel of my scooter when engine is on or should be not rotating i notice that when i center stand my scoot it keep on rotating before it is not rotating...comments...pls
|
|
Freshman Rider
Currently Offline
Posts: 79 
Likes: 7
Joined: Mar 4, 2014 5:05:41 GMT -5
|
Post by ng5y on Jun 3, 2014 16:43:27 GMT -5
I am not sure I understand your question but on the average scooter with a Variator and clutch yes the back wheel should freely turn weather or not the engine is running. Think about it, if it didn't how would you cost to a stop? Also what if it stalled on the road, how would you push it?
If this is a bike with a manual transmission and the bike is in gear, pushing it would be problematic I think.
|
|
Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 3, 2014 16:51:32 GMT -5
when i put it on a center stand engine is running/on the rear wheel is continuously rotating its a 2 stroke scooter.i just noticed that before it is not rotating unless i twist/accelerate it will run/rotate and i just observed that if i brake the rear brake and hold for 10 sec the engine die and when you move the scoot backward for about 3 feet the engine die too..
|
|
|
|
Post by alleyoop on Jun 3, 2014 19:13:18 GMT -5
That means something is wrong in your CVT, either the Variator or the Clutch. Take a picture or VIDEO of it on the center stand with motor running OF THE CVT so we can see the Variator and Clutch.
DID you change anything in the CVT did you change the belt or change the weights in the Variator?
Alleyoop
|
|
Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 3, 2014 19:39:11 GMT -5
no i did not change anything it keep on spinning when on the center stand my wieght is 9grm.and when i hold the rear brake the engine dies
|
|
|
|
Post by alleyoop on Jun 3, 2014 19:44:31 GMT -5
Well you changed something how else would you know it has 9 gram weights. So take the CVT cover off and take a picture of it without the motor running so I can see the variator belt and clutch. Something is wrong in there.
ALleyoop
|
|
Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 4, 2014 7:01:43 GMT -5
 i find the culprit the cable throttle is mess up i cut it before when i change my carb to 21 oko i guess the tape/glue is not working well so when i check it this morning the rear wheel still spinning but when i touch those cable in the px spinning in my rear wheel stop w/ good idle... |
|
Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 4, 2014 7:12:43 GMT -5
now i have to buy a new throttle cable.. i am thinking of buying a clutch kit i thought that's the problem thanks admin..for help and saving my money...
|
|
Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 4, 2014 13:54:43 GMT -5
 this is a video but i don't know how to download it.. |
|
Freshman Rider
Currently Offline
Posts: 85
Likes: 1
Joined: Mar 28, 2013 0:44:33 GMT -5
|
Post by chamisataza on Jun 4, 2014 14:04:39 GMT -5
 this is a temporary fixed on my cable throttle i put cable ties and masking tape... |
|
|
|
Post by alleyoop on Jun 4, 2014 15:24:31 GMT -5
Ah, so the cable came out and was pulling the slide up causing it to idle high. Yes get a new cable. Also to load a VIDEO when you go to TINY PIC you have to CLICK ON VIDEO it loaded it up as a picture. Alleyoop  |
|
..BAD TO THE BONE..