|
|
Post by chris5527 on Jan 10, 2014 18:46:20 GMT -5
Can I put a a9 cam in my stock gy6? Don't bash to hard fellas lol.
|
|
|
|
Post by carasdad on Jan 10, 2014 18:58:53 GMT -5
Can I put a a9 cam in my stock gy6? Don't bash to hard fellas lol. Yup... |
|
|
|
Post by chris5527 on Jan 10, 2014 19:00:29 GMT -5
Can I put a a9 cam in my stock gy6? Don't bash to hard fellas lol. Yup... [br Thank you sir..  that will be my next buy. |
|
|
|
Post by millsc on Jan 10, 2014 19:06:49 GMT -5
If your going to go that far might as well take out the two engine bolts and put on a big bore kit
|
|
|
|
Post by chris5527 on Jan 10, 2014 19:24:26 GMT -5
If your going to go that far might as well take out the two engine bolts and put on a big bore kit That's my next step I'm doing it all on a budget I have a wife two kids and one on the way so the scooter comes last but it will happen  |
|
|
|
Post by carasdad on Jan 10, 2014 19:54:51 GMT -5
If your going to go that far might as well take out the two engine bolts and put on a big bore kit That's my next step I'm doing it all on a budget I have a wife two kids and one on the way so the scooter comes last but it will happen Only prob I have seen..was one engine that had 69mm valves..the cam lift was so high on those longer springs that it caused a slight spring bind. But that is less than a 1 in 100 chance I'm sure. Some have gone with heavier valve springs to avoid valve float from the high lift..but I have yet to actually see one suffer from that. I put an A9 cam in every gy6 50 that I 'Big Bore' cause like millsc says.. "If yer already in there..may as well do it all and be done" But I understand money limits.. I am a father of 6 kids..so been there Sir..  |
|
|
|
Post by millsc on Jan 10, 2014 20:36:25 GMT -5
|
|
|
|
Post by chris5527 on Jan 10, 2014 21:42:30 GMT -5
wow that's not bad at all hmmmm I think I changed my mind |
|
|
|
Post by chris5527 on Jan 10, 2014 21:43:00 GMT -5
And its located a hour from me haha
|
|
|
|
Post by millsc on Jan 10, 2014 21:49:56 GMT -5
The kit works just fine comes with head new rockers and even the jet I have installed it many times big improvement over stock.
|
|
|
|
Post by chris5527 on Jan 10, 2014 21:54:05 GMT -5
The kit works just fine comes with head new rockers and even the jet I have installed it many times big improvement over stock. so with this kit until I get the cam I just slap the stock one in? |
|
|
|
Post by millsc on Jan 10, 2014 21:55:14 GMT -5
|
|
|
|
Post by chris5527 on Jan 10, 2014 21:55:25 GMT -5
Also would stock exhaust hurt it?
|
|
|
|
Post by millsc on Jan 10, 2014 21:58:02 GMT -5
Yes use the stock cam does just fine the cam works to its full potential with a head with bigger valves, open air filter and free flow exhaust.
|
|
|
|
Post by millsc on Jan 10, 2014 21:59:55 GMT -5
Stock pipe the big bore kit and an open air filter you'll be good to go.
|
|
