|
|
Post by ksaun123 on Oct 9, 2014 3:41:01 GMT -5
So I decided to install the 150cc piston kit and was wondering about the 1st and 2nd rings. Which one goes on top and which one go in the middle? I got a silver and a black one. I already jnstalled the kit but u was looking at some videos and some people had them certain kinds of ways. Im good on the bottom oil seal rings on the piston. I made sure i didnt line up the gaps on the rings. alleyoop tvnacman katastroff |
|
Freshman Rider
Currently Offline
Posts: 59 
Likes: 11
Joined: Oct 3, 2014 20:29:15 GMT -5
|
Post by katastroff on Oct 9, 2014 7:13:19 GMT -5
1- Silver ring
2-Black ring
3-4-5- Oil rings
Don't forget to gap them properly.
|
|
|
|
Post by ksaun123 on Oct 12, 2014 11:10:19 GMT -5
ksaun123, katastroff alleyoop just a little update: bought a new cylinder, corrected the rings, and got new oil.   it runs now!!!! since i just got a muffler head, its pretty loud. it has a oil leak behind the cylinder. must be the gasket. im just going to use a gasket maker...
|
|
Freshman Rider
Currently Offline
Posts: 59
Likes: 11
Joined: Oct 3, 2014 20:29:15 GMT -5
|
Post by katastroff on Oct 12, 2014 12:51:30 GMT -5
Have you used a torque wrench to tighten your bolts?
|
|
|
|
Post by dmartin95 on Oct 12, 2014 13:03:24 GMT -5
Have you used a torque wrench to tighten your bolts? This is weird... I just linked to a thread you had started on scootdogs forumThere's a handful of members here (myself included) that suffers from the scooter losing power at WOT with the same retro style scooter as in your pic.... Will you join our thread here and fill us in on your results with the Mikuni fuel pump? |
|
|
|
Post by alleyoop on Oct 12, 2014 13:15:03 GMT -5
Where Is the Fuel Pump mounted in relation to the tanks fuel outlet and the carb?
If you could take some pictures of the tanks fuel outlet going to the fuel pump and then to the carb would help.
Alleyoop
|
|
|
|
Post by ksaun123 on Oct 12, 2014 13:32:09 GMT -5
|
|
|
|
Post by xyshannen on Oct 12, 2014 13:48:00 GMT -5
Your head bolts should be torqued to spec @ 15 foot pounds. I'm in the process of doing this very thing to my 150cc gy6 and that is the torque specs i've found for our engine head bolts. not torquing them to spec risks gasket blow outs and oil leaks at the very least. |
|
|
|
Post by dmartin95 on Oct 12, 2014 13:49:47 GMT -5
I'm heading out the door at the moment but I'll get some shots later.
l8r ya'll!
|
|
|
|
Post by ksaun123 on Oct 12, 2014 14:51:23 GMT -5
Alright so all i have to do is buy top end gaskets and torque them to 15 foot lbs? xyshannen |
|
|
|
Post by xyshannen on Oct 12, 2014 15:20:03 GMT -5
Alright so all i have to do is buy top end gaskets and torque them to 15 foot lbs? xyshannenJust to clarify..not your valve cover bolts, the bolts that go on the cylinder jug studs. Yes 15 foot pounds is the spec for the torque of those bolts. |
|
|
|
Post by ksaun123 on Oct 12, 2014 23:55:02 GMT -5
the oil is leaking, not the gas. alleyoop |
|
..BAD TO THE BONE..
