|
|
Post by geh3333 on Dec 31, 2015 21:15:54 GMT -5
Good job ! You can eliminate the vacuum valve all together. The float valve will close the fuel off when the bowl is full. Many ATVs are setup that way. Well actually they do have a manual shutoff , but you can add one anytime. I never turned mine off unless I way working on it.
|
|
|
|
Post by ricardoguitars on Dec 31, 2015 21:36:01 GMT -5
Good job ! You can eliminate the vacuum valve all together. The float valve will close the fuel off when the bowl is full. Many ATVs are setup that way. Well actually they do have a manual shutoff , but you can add one anytime. I never turned mine off unless I way working on it. It depends on the carb, mine leaks if I leave the shutoff valve open. |
|
|
|
Post by geh3333 on Jan 1, 2016 14:58:49 GMT -5
Good job ! You can eliminate the vacuum valve all together. The float valve will close the fuel off when the bowl is full. Many ATVs are setup that way. Well actually they do have a manual shutoff , but you can add one anytime. I never turned mine off unless I way working on it. It depends on the carb, mine leaks if I leave the shutoff valve open. If your carb leaks then the float valve is prob bad. |
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62 
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 17:32:47 GMT -5
One more problem... Battery is fully charged now and it's not that, if I have the key in standby position the little lcd clock comes on on the dash. If I turn the key to the on position the clock goes off and the bike appears to lose all power. Any thoughts, I wires the ignition up matching the colours red from the harness to red on the ignition black on harness to black on ignition etc thinking that the ignition switch changes them depending on key position I'm now thinking do they need to not match anyone got a 4 wire ignition I'm sure they are for the most part the same... Any help much appreciated!
|
|
|
|
Post by tvnacman on Jan 1, 2016 18:01:51 GMT -5
key off zero ohms green to black/white
key on zero ohms red to black
John
|
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 18:06:15 GMT -5
Sorry please explain a little more my electrical skills are not the best...
hopefully this will help i checked with multimeter
key off
red - black 9
red - green 9
red - stripe 9
key on
red - black 0
red - green 1.7
red - stripe 1.7
|
|
|
|
Post by tvnacman on Jan 1, 2016 18:19:17 GMT -5
unplugged the switched side?
John
|
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 18:20:23 GMT -5
Huh?
|
|
|
|
Post by tvnacman on Jan 1, 2016 18:23:32 GMT -5
did you ohm it out with the switch unplugged?
John
|
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 18:26:15 GMT -5
No I have the ignition wires up to the harness red to red black to black green to green stripe to stripe. With it wires up like this with the key on and off I get the results above if that makes sence
|
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 18:32:10 GMT -5
|
|
|
|
Post by tvnacman on Jan 1, 2016 18:37:41 GMT -5
put the pointer at 6 oclock, and check the switch . It must be unplugged from the scooter.
John
|
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 19:23:20 GMT -5
Ok key in on position red to black gets a connection anything to anything else gets nothing and I tried all the connections
key in off position nothing on any connection
|
|
Freshman Rider
Currently Offline
Jonway Madness YY50QT-31 2014 (now made of more replacement parts than original)
Posts: 62
Likes: 3
Joined: Oct 30, 2014 15:22:20 GMT -5
|
Post by username on Jan 1, 2016 19:38:32 GMT -5
So ignition only seems to do one thing in on position it connects red and black.
Connected wires back up and same happens
|
|
|
|
Post by tvnacman on Jan 1, 2016 19:56:49 GMT -5
can you post a picture of the switch?
show the wires and the plug your plugging it into with wire colors.
from what your telling us it sounds like a bad switch.
John
|
|
