New Rider
Currently Offline
Posts: 7 
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Post by kmartsocca on Aug 8, 2016 16:40:50 GMT -5
Last week turn signals on Ice Bear 300 PMZ-11 stopped working. When turned on emergency flashers came on. Then, the emergency flashers stayed on. Cannot t find a flasher box and the switch looks fine.
Any ideas?
|
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Solenoid
by: kmartsocca - Feb 8, 2016 19:03:31 GMT -5
via mobile
Post by kmartsocca on Feb 8, 2016 19:03:31 GMT -5
When I first got my 300cc Icebear scooter, it would not start and found it had a bad solenoid. It was a new scooter but a floor model so it had been sitting. Now after being away for three weeks, the scoot will not start, turn over. Sounds exactly the same as when the solenoid was bad so I'm assuming a bad solenoid again. Question is, does this part go bad from just sitting or is there another reason this keeps happening. Attempted to contact the dealer but of course it's after hours
|
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Post by kmartsocca on Dec 30, 2015 19:19:30 GMT -5
There was a copper colored washer, no o ring or rubber washer. Found a bolt that was just a minor amount larger, was afraid to crack the aluminum gear box so did not over tighten and this seemed to do the job.
Thank you, just another dumb lady trying to be a do it yourselfer
|
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Post by kmartsocca on Dec 29, 2015 14:32:21 GMT -5
Just changed gear oil on the Ice Bear PMZ 300-11. As the plug was removed there were several pieces of aluminum threads. As the plug was put back I was unable to tighten it, leaving it dripping at a slow rate. I did have a ever so larger bolt that I used which alleviated the drip. Will this be a problem? Do I need to have the gearbox rethreaded or will this be okay?
|
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Seat bucket
by: kmartsocca - Dec 24, 2015 15:04:39 GMT -5
via mobile
Post by kmartsocca on Dec 24, 2015 15:04:39 GMT -5
Guess I don't need the bucket off--wiggled my hand under and got the solenoid back on the bracket.
Thank you
|
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Post by kmartsocca on Dec 24, 2015 11:53:55 GMT -5
Thank goodness for this site, as many of my minds questions had been answered. Have just went from a 150cc to a 300cc scooter.  |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Dec 24, 2015 10:59:18 GMT -5
|
Seat bucket
by: kmartsocca - Dec 24, 2015 11:16:23 GMT -5
via mobile
Post by kmartsocca on Dec 24, 2015 11:16:23 GMT -5
Does anyone know to remove the seat bucket on a 300cc Ice Bear Cosmo? I need to get the solenoid back on the bracket and the easy way would be bucket off.
Suggestions? Ideas?
|
|
