New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Gy6 problems
by: organdoughnut - Mar 23, 2013 5:48:48 GMT -5
Post by organdoughnut on Mar 23, 2013 5:48:48 GMT -5
Ill recheck all the carb, yeah it is soaking after 2 mins of kicking it  |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Gy6 problems
by: organdoughnut - Mar 22, 2013 16:04:21 GMT -5
Post by organdoughnut on Mar 22, 2013 16:04:21 GMT -5
Heya guys, I'm having massive issues with this longjia digita 51 (2011 plate ) with a gy6 50cc engine, before November the bike was running fine then it needed a valve adjustment, he said he removed the fan to find tdc re-adjusted the valves to 0.004 inlet and 0.003 exhaust, the bike was running great so he went for a spin to make sure everything is ok when he came back he went to bolt on the fan and used the wrong bolts crushing the stator, he then asked for my help so I replaced the stator ( 4 months later Because it took scrappy dog scooters 4 months to deliver it which is stupid, so 4 months later I replace the generator and the battery and the spark plug, the bike is now sparking again but when he went for a ride it ran for 1 minuet then died and it has not been the same since, changed the fuel , re - adjusted the valves, checked timing , cleaned carb , but when I try and start the bike it runs for 5 seconds then dies and takes ages to re-start. There is loads of fuel coming out of the air inlet on the carburetor, the float is not sticking and the carb is clean, do you guys have any suggestions ? Because I'm stumped Thanks guys and girls, Danny |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Post by organdoughnut on Mar 3, 2013 14:09:17 GMT -5
thanks allot guys ill test this as soon as i can  |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Post by organdoughnut on Mar 3, 2013 11:54:36 GMT -5
yeah all the brake lights work |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Post by organdoughnut on Mar 3, 2013 11:48:00 GMT -5
|
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Post by organdoughnut on Mar 3, 2013 11:25:43 GMT -5
brilliant thanks |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Post by organdoughnut on Mar 3, 2013 11:03:02 GMT -5
thanks this may sound stupid whats he best way of doing that ?  |
|
New Rider
Currently Offline
Posts: 7
Likes: 0
Joined: Mar 3, 2013 10:34:10 GMT -5
|
Post by organdoughnut on Mar 3, 2013 10:42:43 GMT -5
Hello guys,
i have a 50cc 2 stroke 1PE40-QMB Scooter and my friend bought it from me in september, somehow in december he managed to snap the bike in two ( front end fell off ) and he broke his leg so it was left outside for 3 months with no front body pannel and the bike was uncovered. i have the task of restorig the bike to be used again but when i turn the ignition the dash and indecators work etc but when i press the starter button ( with the brake pressed ) the starter motor isnt cranking the engine. but when i short the starter solinoid it does. it never has any issues like this before the bike snapped do you guys have any idea how i can diagnose or find where the fault is,
thanks again, Danny
|
|
