Freshman Rider
Currently Offline
Posts: 58
Likes: 0
Joined: May 10, 2013 19:02:38 GMT -5
|
what to do
by: biguns420 - May 12, 2013 16:20:39 GMT -5
Post by biguns420 on May 12, 2013 16:20:39 GMT -5
what do you do, about cracking the pickup bar? on a 1e40qma motor? its cracked there, int this picture and at the other side on the case. ill upload a pic. can it be used?   |
|
|
|
what to do
by: jeepsteve92xj - May 12, 2013 16:58:25 GMT -5
Post by jeepsteve92xj on May 12, 2013 16:58:25 GMT -5
A weld/braze, or replace.
|
|
|
|
what to do
by: teddy554 - May 12, 2013 19:36:05 GMT -5
Post by teddy554 on May 12, 2013 19:36:05 GMT -5
Buy a new stator and replace the whole thing for 50-60 bucks. how you break it. you will need a flywheel puller
|
|
|
|
what to do
by: jeepsteve92xj - May 12, 2013 20:04:47 GMT -5
Post by jeepsteve92xj on May 12, 2013 20:04:47 GMT -5
Of course if one is replacing the stator to make a repair, one may think about performing an upgrade at once.
|
|
|
|
what to do
by: teddy554 - May 12, 2013 20:05:44 GMT -5
Post by teddy554 on May 12, 2013 20:05:44 GMT -5
i want to know how did he break it
|
|
|
|
what to do
by: scootnwinn - May 12, 2013 21:39:42 GMT -5
Post by scootnwinn on May 12, 2013 21:39:42 GMT -5
Me too. I say rocks
|
|
Freshman Rider
Currently Offline
Posts: 58
Likes: 0
Joined: May 10, 2013 19:02:38 GMT -5
|
what to do
by: biguns420 - May 12, 2013 21:41:26 GMT -5
Post by biguns420 on May 12, 2013 21:41:26 GMT -5
it looks like part of the case. i was thinking, it was just back bracing the pickup, and holding a bracket that held the stator wire. it has a metal backplate between the pickup and the other screw where its broke. could just bend the metal brace back, and it would hold the piece that holds the bracket, and hold it, in that, or its aluminum. can epoxy work? what kind of aluminum welding?
|
|
|
|
what to do
by: devo344a - May 12, 2013 22:09:52 GMT -5
Post by devo344a on May 12, 2013 22:09:52 GMT -5
Put JB weld on it use the pickup to hold it in place from the pic it would be hard to weld the case doesnt look like theres much material left on the case
Ive used JB weld on alot of things get some carb cleaner to clean it so it gets the dirt out in the tiny holes the most important thing to do is make sure you let it dry ive gotten in a hurry and broke it because i didnt let it dry
|
|
Freshman Rider
Currently Offline
Posts: 58
Likes: 0
Joined: May 10, 2013 19:02:38 GMT -5
|
what to do
by: biguns420 - May 13, 2013 0:42:33 GMT -5
Post by biguns420 on May 13, 2013 0:42:33 GMT -5
it was, either broke before i got it, or i pried on it and done it. .. i wasnt prying that direction. .. idont know.
|
|
|
|
what to do
by: teddy554 - May 13, 2013 7:26:03 GMT -5
Post by teddy554 on May 13, 2013 7:26:03 GMT -5
This is what is broke Attachments:
|
|
Freshman Rider
Currently Offline
Posts: 58
Likes: 0
Joined: May 10, 2013 19:02:38 GMT -5
|
what to do
by: biguns420 - May 13, 2013 10:56:10 GMT -5
Post by biguns420 on May 13, 2013 10:56:10 GMT -5
oh well. do you think it would, pickup, the same. how close, does the pickup have to be to fire right. how much would set it off. too much. what if it was 1 degree, is that 1 degree around it?
1 degree off. i thik i can find a 4 stroke one. i need a flywheel puller. does geniune parts match up, some cvt's are close?
|
|
